The features it recognises
The engine keeps a detector for each of the shapes a part carries, and each one knows how its own shape is dimensioned on a drawing: a rebate is measured as a rebate and a bore as a bore, not as an anonymous edge. The complete list of those detectors stands below — built from the detectors themselves, never written out here.
Readable text, by rule not by guess
Text height comes from a fixed ladder of paper millimetres, assigned by the role a label plays; it never scales with the size of the part. Text width is measured from the font file itself, so a dimension never collides with the next one because its width was estimated.
Assemblies are split first
An uploaded assembly is separated into its individual parts before dimensioning, so every part gets its own dimensioned sheet. You upload the model you already have; you do not prepare a part list first.
What gets dimensioned — the complete list
Every feature the dimensioning engine detects and dimensions, with the measurements it produces. This list is complete: it is built from the detectors themselves, not typed out.
Cut-outs and birdsmouths
- cut-out
- A cut that goes through the board and is open at an edge: width, length and position.
- slot
- The same cut once the depth reaches at least twice the width of the opening — then the cut carries its own name, with width, length and position.
- birdsmouth
- Apex position, apex depth and both saw tilts, each at a real corner — through, part-width, or at the end of the part.
- diagonal V-notch
- Both wall crossings chained along the border, the angle at each corner and the depth at a real point — never a dimension to the apex in mid-air.
Grooves, pockets and rebates
- groove
- Width, depth, length and position, in any direction of the part; every corner radius gets its own leader.
- A channel closed at both ends: everything a groove gets, plus its position along the run.
- diagonal housing
- Tool width, run angle at a real corner, the crossings at both borders, and the depth.
- rebate
- Both legs, the length, and a position at every stopped end; a corner fillet never enlarges a leg.
Tenons and mortises
- tenon
- The length along each tongue edge wherever a sloped shoulder or a bevelled tip makes them differ, plus width, thickness and the offsets across and along; the shoulder and the tip are given as tilts off the square cut, and a peg bored through the tongue gets its diameter and both its offsets.
- mortise
- The tenon's counterpart wherever neither groove nor pocket already describes the hole — a sloping floor, or walls set at an angle in plan: the length square to the walls, the width, both positions, the angle, and a depth at EACH end wall rather than one note that could belong to either; where the walls lean through the depth, the mouth length as well.
Mitres and chamfers
- mitre
- The saw angle referenced to the square stock — a 45° cut reads 45°, never the body diagonal — plus the cut legs; a lengthwise mitre gets the acute angle at its base edge.
- chamfer
- Both leg distances, stated once with a count where several chamfers are identical. The chamfer angle itself is never dimensioned — at 45° the equal legs state the angle; any other angle has to be worked out from the legs.
- wedge strip
- The two perpendicular legs of the triangular section — the stock sizes you cut from, never the hypotenuse as a “width”.
Bores and radii
- hole
- Diameter in any direction, with the depth folded in for a blind bore, the centre from two datum faces; a row of identical bores becomes one callout with a single pitch.
- fillet
- Every rounded edge gets its radius, equal radii gathered part-wide into one callout.
On top of that, every part carries its overall size — length, width and thickness, measured to the true extent, never across a diagonal.
What is not dimensioned
We would rather leave a dimension off than print one we cannot place correctly: a measurement with no lawful place on the sheet is recorded as skipped and named, never guessed. Dovetails, lap joints, stepped bearing joints and threads have no detector of their own — a part carrying one still comes back, with its overall size and every feature in the list that it also carries.
Common questions
Which shapes can it dimension?
Cut-outs and birdsmouths · Grooves, pockets and rebates · Tenons and mortises · Mitres and chamfers · Bores and radii — on beam- and panel-shaped parts. The complete list, with the measurements each feature produces, stands on this page; every shape has its own dimensioning rules built into the engine.
Does the text get smaller on large parts?
No. Text height is fixed by role in paper millimetres and does not scale with part size, so a big part reads exactly as clearly as a small one.
Do I need to place any dimensions myself?
No. The dimensions are placed automatically. You can then download the result and adjust it in your own CAD if you wish.
What is not dimensioned?
We would rather leave a dimension off than print one we cannot place correctly: a measurement with no lawful place on the sheet is recorded as skipped and named, never guessed. Dovetails, lap joints, stepped bearing joints and threads have no detector of their own, and a chamfer's angle is never dimensioned — only its two legs. A part carrying such a joint still comes back, with its overall size and every feature in the list that it also carries.
Try it now, free
Upload a CAD file and see the dimensioned preview at once, free, with no account; you pay only on download.